Crosslinking Agents
Product Characteristics
INSODUR RF Similar to INSODUR RFE PLUS, but with moderate crosslinking speed and longer pot-life. Less coloured.
INSODUR RFE PLUS Solvent based hardener of the poly-isocyanate type. To crosslink solvent based adhesives of polychloroprene and polyurethane rubber. Very high crosslinking speed. The pot-life is relatively short. Slightly yellow colour.
RETICULANTE DA Liquid poly-isocyanate for solvent-free soling adhesives and primers. (AQUATACK)
Hot-Melts
Product Characteristics
CORDÓN PA MONTADO Lasting (rod), polyamide-based.
CORDÓN PA TOPES Thermoplastic toe-puffs (rod), polyamide-based.
CORDÓN UPE MONTADO Lasting (rod), polyester-based.
GRANZA PA Folding (pellets), polyamide-based.
GRANZA PA TOPES Folding (pellets), polyamide-based. Toe-puffs.
Lasting and Heel-Covering
Product Characteristics
MONTAROL 260 F Contact adhesive for same applications as MONTAROL 7127 ST but to use with textiles and other very porous materials. Clear colour.
MONTAROL 260F/2000 TOLUENE FREE version of MONTAROL 260F with same properties.
MONTAROL 8100 Contact adhesive for lasting, with wide open time and moderate heat resistance.
MONTAROL 8200 Fast contact adhesive for lasting with high heat resistance an medium to high viscosity.
MONTAROL 8210 TOLUENE FREE version of MONTAROL 8200 with similar properties.
MONTAROL HORNO 450 Contact adhesive for machine lasting with good heat resistance and 30min open time.
MONTAROL HORNO 500 TOLUNE FREE contact adhesive for lasting or weave jute soles for later vulcanization.
MONTAROL RC For machine lasting. For covering plastic heels. This is a widely used cement in the leather goods industry for permanent fixing. Good heat resistance and tack.
MONTAROL UPE 2000 TOLUENE FREE version of MONTAROL HORNO 450 with similar properties.
MONTAROL UPE-2000/VISCOSO High viscosity version of MONTAROL UPE-2000.
ROK 100 High and fast initial strength version of ROK 70.
ROK 69-S Non stain contact adhesive for lining and lasting. To bond upper to sole is possible as two component.
ROK 69-S/2000 TOLUENE FREE version of ROK 69 with same properties.
TAKIFLEX 390 Standard lasting contact adhesive with slow evaporation rate and medium tack.
TERMOFLEX Contact adhesive for machine lasting or lining hells with good heat resistance and good tack.
Lining-Combining-Folding and Counter Bonding
Product Characteristics
CEBESTAR 5 Polychloroprene adhesive with long open time, high tack, high viscosity and non stain for combining, folding, upper leather lining and for the production of insoles.
CEBETACK 670 One way contact adhesive with good adhesion to strip, salpa and leather board. High viscosity with high solid content and good machinability.
CEBETACK 670/2000 TOLUENE FREE version of CEBETACK 670 with same properties.
CEMENT 5000 Standard natural rubber-based (NR) cement with high viscosity for combining and folding with porous materials.
CEMENT 7000 Modified NR cement with improved heat resistance and suitable to be used with greasy leathers.
CEMENT 7000/ST TOLUENE FREE version of CEMENT 7000 with same properties.
CEMENT B Standard natural rubber-based (NR) cement for combining and folding.
CEMENT B/A NR cement for combining and lining one-way cementing to avoid soaking.
CEMENT EXTRA Standard natural rubber-based (NR) cement for combining and folding.
CEMENT EXTRA MÁQUINA Standard natural rubber-based (NR) cement with low viscosity for combining and folding.
DISOLUCION T-96N Natural rubber-based (NR) cement with medium to low viscosity, high solid content and non stain for combining and folding.
MONTAROL 1W/F Cold bonding contact adhesive with long open time and excellent tack. Self-adhesive with good tack, very strong cohesion and moderate resistance to heat, with sufficient viscosity for application by machine or brush.
MONTAROL 260 F/NS Contact adhesive for same applications as MONTAROL 7127 ST but to use with textiles and other very porous materials. Clear colour.
MONTAROL 270 Contact adhesive to made moulding insoles, lining or lasting leather uppers.
MONTAROL 270 FT/2000 TOLUENE FREE contact cement with long cold open time and good tack level, with low viscosity for roller application to use in insoles with or without shank.
MONTAROL 27ST-BV Contact cement with long cold open time and good tack level, with low viscosity. Economic contact adhesive, generally used in the shoe industry and the leather goods industry.
MONTAROL 27ST-FF Contact cement with long cold open time and good tack level, with very low viscosity. Economic contact adhesive, generally used in the shoe industry and the leather goods industry.
MONTAROL 27ST-FF/2000 TOLUENE FREE version of MONTAROL 27ST-FF with same properties.
MONTAROL 27ST-VISCOSO Contact cement with long cold open time and good tack level, with high viscosity for porous materials. Economic contact adhesive, generally used in the shoe industry and the leather goods industry.
MONTAROL 27ST-VISCOSO/2000 TOLUENE FREE version of MONTAROL 27ST-VISCOSO with same properties.
MONTAROL 7127 ST Contact adhesive with a very long open time and a very high tack for cold lasting, combining, folding, upper leather lining and for the production of insoles.
MONTAROL 8130 Contact adhesive with a very long open time and a very high tack for folding, upper leather lining and for the production of insoles. Non stain.
MONTAROL MA-1W Pressure-sensitive Polychloroprene cement to be used in one-way cementing machines for production of insoles.
MONTAROL MA-1W/ESPECIAL One way adhesive with very high tack, high initial strength and medium to low heat resistance.
MONTAROL MA-1W/TV One way contact adhesive with high initial strength with good adhesion to difficult insoles materials.
MONTAROL MA-1W/TV-2000 TOLUENE FREE version of MONTAROL MA-1W/TV with same properties.
MONTAROL PLANTAS B1 Economy contact adhesive with good adhesion to strip, salpa and leather board to made insoles. High viscosity and good machinability.
MONTAROL PLANTAS CH TOLUENE FREE Contact adhesive formulated for one-way wet bonding of socks to PVC or patent leather lined insoles.
MONTAROL PLANTAS H Standard TOLUENE FREE adhesive for one-way wet bonding of socks to insoles.
MONTAROL PLANTAS H/T VISCOSO Same works as MONTAROL PLANTAS H but to use with extremely porous socks.
MONTAROL PLANTAS P TOLUENE FREE contact adhesive for one-way wet bonding of socks to PVC lined insoles.
PLASTIKOL P-500 COLD BONDING polyurethane adhesive designed for synthetic materials (e.g. PVC, PU), leather goods, wallets, etc. and for auxiliary works as lining, folding, lasting before sewing or bonding insoles.
ROK 70 Contact adhesive with long open time, high tack and non stain for lasting, combining, folding, upper/sole bonding of textile or jute.
ROK 70/2000 TOLUENE FREE version of ROK 70 with same properties.
ROKENE 315 Non stain contact adhesive with long open time and high tack to use with textiles and other very porous materials.
Primers and Adhesion Promoters
Product Characteristics
ENEDUR 100 Primer for thin leathers to simplify the roughing process.
IMPRIMER CR-1 Solvent based CR low viscosity primer for leather soles and other materials difficult to penetrate. One component. Brushable and roller machine.
IMPRIMER PUR-3 Solvent-based polyurethane (PUR) primer, specially used in the shoe industry, as a primer for rubber, TR, PVC and polyurethane soles, suitable pre-treated. Also suitable as a primer for leathers and other porous materials.
IMPRIMER PUR-6 Two component primer use to prepare TPU.
INESTRAT G Solvent based one component primer to avoid deep roughing of certain leather uppers and to reinforce them.
INSOCOL IMPRIMACIÓN 3000 Solvent based polychloroprene (CR) primer of 2 components, for the preparation of EVA microcellular sole and EVA/SBR (Toflex, Torplas) avoiding roughing and allowing storage prior to cementing with polyurethane solvent or water base to leather or plastic uppers. Brushable.
INSOCOL IMPRIMACIÓN 3000/ST TOLUENE FREE version of INSOCOL IMPRIMACIÓN 3000 with same properties.
PRIMER EVA 300 Solvent based two component primer for the preparation of EVA microcellular sole for a later PU water based bonding.
PRIMER EVA-100 Solvent based one component primer for the preparation of EVA microcellular sole and EVA/SBR (Toflex, Torplas) previously roughing.
PRIMER PA-97 Primer for polyamide soles and flexible PEBA soles (i.e.. football shoes, cycling shoes, etc.). 2K , without phenol.
PRIMER PS-9902 One component primer for direct injection of PS heels onto leather linings.
PRIMER TR-100 One component primer for direct injection of TR soles onto leather linings.
PRIMER UV-078/I Solvent-based primer for bonding moulded EVA units, without roughing, using UV light exposure.
SOLUCIÓN HALOGENANTE One component halogenation solution, stable for 6 months under adequate storage conditions. Used for preparation of vulcanized rubber SBR and thermoplastic rubber (TR) soles prior to cementing with polyurethane adhesives.
Upper/Sole Contact Bonding
Product Characteristics
CEBESPRINT P-217 Slow drying contact adhesive with high viscosity and solid content. Very high heat resistance.
CELLOPRENE 1075/NS For bonding textile footwear, canvas upper to jute sole. Light coloured. Open time 30-45 minutes. Light coloured. One or two components.
CELLOPRENE 1080 For bonding leather, MP-EVA and microcellular rubber soles to leather uppers.
CELLOPRENE 2000 TOLUENE FREE version of CELLOPRENE BRC with similar properties.
CELLOPRENE 2000 PISTOLA Sprayable version of CELLOPRENE 2000
CELLOPRENE 2000/V High viscosity version of CELLOPRENE 2000
CELLOPRENE 2156/NS Less stain version of CELLOPRENE 1075/NS with similar applications
CELLOPRENE B ESPECIAL Same as above and moreover to bond gristle-rubber soles to leather uppers. Shorter open time (15 minutes) and higher green strength.
CELLOPRENE BRC For bonding leather, resin-rubber EVA and microcellular rubber soles to leather uppers. High initial strength and good heat resistance. Standard 30 minutes open time.
INSOCOL 2889 For cementing textile footwear, canvas uppers to jute soles. Clear colour. Two components.aro.
INSOCOL 2889/ST TOLUENE FREE version of INSOCOL 2889 with same properties.
INSOCOL 8500 Similar to INSOCOL GTR but with short open time a low tack.
INSOCOL 8500/2000 TOLUENE FREE version of INSOCOL 8500 with same properties.
INSOCOL 8510 Fast one or two component contact adhesive to place trims/ornaments
INSOCOL GTR Standard two components adhesive for bonding vulcanized rubber, crêpe, cellular and microcellular rubber, EVA as well as leather soles to leather uppers. For insole to rubber sole bonding. 30 minutes open time.
INSOCOL GTR/2000 TOLUENE FREE version of INSOCOL GTR with same properties.
INSOCOL NS-1 For bonding microcellular rubber, gristle rubber soles to textile uppers. Light coloured. Same applications than GTR with longer open time.
INSOCOL PRF Standard one or two component contact adhesive to use in pre-assemble works. Non stain
INSOCOL SR Very fast two component contact adhesive with high heat resistance.
ROK 97 TR Two components contact adhesive for bonding vulcanized rubber, crêpe, cellular and microcellular rubber, EVA as well as leather soles to leather uppers or BIOS. For insole to rubber sole bonding.
ROK FLEX Two components contact adhesive for bonding vulcanized rubber, crêpe, cellular and microcellular rubber, EVA as well as soft rubber on climbing shoes.
ROK FLEX/2000 TOLUENE FREE version of ROK FLEX with same properties.
ULTRAFLEX Standard contact adhesive with good tack level, high initial strength and good heat resistance.
Upper/Sole Heat Reactivation Bonding
Product Characteristics
PLASTIFLEX 88 Similar to 553 BV, with higher viscosity and solid content, suitable for very absorbent materials.
PLASTIFLEX 88/2000 TOLUENE FREE version of PLASTIFLEX 88 with same properties.
PLASTIKOL 2000 TOLUENE FREE Polyurethane adhesive for lasting and sole bonding in sandals.
PLASTIKOL 2000/F Low viscosity version of PLASTIKOL 2000
PLASTIKOL 22A Special type for manufacturing antistatic shoes. Almost colourless and very similar in the other properties to PLASTIKOL 553 BV-RC.
PLASTIKOL 2877 Product with a lower reactivation temperature, suitable for soft materials, and with a longer hot tack time.
PLASTIKOL 2877-V/2000 TOLUENE FREE version of PLASTIKOL 2877-V with same properties.
PLASTIKOL 2877/V High viscosity version of PLASTIKOL 2877
PLASTIKOL 552 Standard type for bonding all types of upper materials (leathers and synthetics) to leather, PVC, polyurethane soles as well as vulcanized rubber and TR soles and in general to all kinds of soles with the suitable previous treatment.
PLASTIKOL 552 BV Polyurethane adhesive for high plasticized PVC soles bonding and for direct injection of PVC and PUR soles to roughened leather and PUR upper materials and also for very rapid cementing processes.
PLASTIKOL 553 Similar to 553 BV, with higher viscosity and solid content, suitable for very absorbent materials.
PLASTIKOL 553 BV Standard type with medium heat reactivation temperature. Specially developed for cementing all types of uppers to roughened resin-rubber soles (to avoid the halogenation treatment) and primed EVA soles.
PLASTIKOL 553 BV/RC TOLUENE FREE Similar as PLASTIKOL 553-BV, with greater initial strength and higher heat resistance. Suitable for very rapid cementing processes.
PLASTIKOL 570 Similar to 553 BV-RC, with more freeze resistance.
PLASTIKOL 600/B TOLUENE FREE Polyurethane adhesive with good reactivation temperature, good initial strength and slow drying rate.
PLASTIKOL 700 Polyurethane adhesive for pre-assembly works on difficult bonding PU soles.
PLASTIKOL P-1HR/68 Standard type for bonding all types of upper materials (leathers and synthetics) to leather, PVC, polyurethane soles.
PLASTIKOL P-4910/D-2 Standard sprayable polyurethane adhesive.
Various
Product Characteristics
AQUATACK 1585 Base for the manufacture of finishes, inks and repairers of extra matt appearance, with an excellent hiding power and adequate flexibility to prevent cracking of the film. For the repairing of cracked or sanded skins, equalizing of edges on belts, etc.
AQUATACK TC DENSO Water based adhesive for upper part lining bonding and posterior mouldering, both with toe puffs and counters as without them.
Also used as Primer for leather reinforcement. Brushable.
AQUATACK TC/S o TC-48 Water based adhesive for upper part lining bonding and posterior mouldering, both with toe puffs and counters as without them.
Sprayable or dipping.
DISOLVENTE 2000 TOLUNE FREE solvent to dilute or cleaning agent for polychloroprene adhesives. Also for cleaning of brochures, spray guns and other application tools.
DISOLVENTE DIFUMINADOR Diluant EXEMPTE DE TOLUÈNE pour la plupart des adhésifs solvents. Dissolvant pour nettoyer des outuils d'application des adhésifs. Nettoyant pour tout les types de graisse et saleté.
DISOLVENTE TOPES Softening solvent for certain types of toes and counters. Solvent and cleaning agent for polychloroprene adhesives.
ENDURECEDOR LEFAX Solvent based primer for toughen insoles by dipping
ENEMELT 500 SBS hotmelt for bonding velcro to leather or textile to be sewn later. Fixing Hotmelt.
ENEMULT RT Water based PVA adhesive for the manufacture of high-density fibreboard (HDF) heels.
INSOCRIL ONE Instant adhesive for the fast bonding on shoe industry, leather, canvas, cardboard, paper, etc. Medium viscosity.
INSOCRIL ONE PLUS Specific Instant adhesive for the fast bonding on shoe industry with high initial strength.
PLASTIKOL P-500 Polyurethane solvent based adhesive for COLD BONDING. Very fast one way adhesive, with good cohesive strength and moderate heat resistance.
TOPLAX Liquid for hardening toe caps, mainly for unlined footwear.
TYROCOL C-10 F/TA Water based adhesive for thermo lamination of leathers and fabrics, double side glueing. Lamination of leathers and synthetics to cotton base in continuous, contacting the leathers or synthetics in wet state.
TYROCOL C-10F / R Water based adhesive for insole manufacture to bond cardboard like LEFAX/TEXON to latex foam or MP-EVA. Roller application.
TYROCOL FG Water based adhesive for lamination of textile to glitter
TYROCOL IG-3 Water based PVA adhesive for the manufacture of high-density fibreboard (HDF) heels. D-3 of DIN EN 204,205
Vulcanization Bonding
Product Characteristics
CELLOPRENE 4040 Vulcanization adhesive for natural rubber and SBR soles to canvas uppers or jute soles, very absorbent, as adhesive with long open time and high tack.
CELLOPRENE 5050 Similar to CELLOPRENE 4040 but faster, short open time and high heat resistance
VULCOL 100 Adhesive indicated for press vulcanization of rubber to leather uppers.
VULKENE Adhesive indicated for direct vulcanization of NBR soles to leather uppers.
Water Base Adhesives (AQUATACK)
Product Characteristics
AQUATACK 100 Water based contact adhesive high speed of coagulation by pressure for leather goods, wallets, etc. and for auxiliary works as lining, folding, lasting before sewing or bonding insoles. Application by brush or roller.
AQUATACK 1K / 891 Polyurethane water dispersion based ONE COMPONENT adhesive. Recommended for the most common sole materials (PUR, PVC, Rubber, Leather, TR, Cork/Latex BIOS) to synthetic or natural uppers as well as for lamination of these materials. Spray application.
AQUATACK 200 SR-7 Modified natural latex for combining and other hand-made auxiliary works in shoemaking, for the production of insoles. High tack and long open time. Soft and flexible adhesive joints. Sprayable. Contact bonding.
AQUATACK 200 SR-7/V-UV Sprayable high viscosity version of AQUATACK 200 SR-7 for porous substrates with UV tracer.
AQUATACK 200 SR/5 Modified natural latex for combining and other hand-made auxiliary works in shoemaking, for the production of insoles. Very high tack and long open time. Soft and flexible adhesive joints. Sprayable. Contact bonding.
AQUATACK 200 SR/75 Version of AQUATACK 200 SR-7 with better resistance to temperature for substrates which are going to be dry by oven.
AQUATACK 2000/CB Sprayable water based COLD BONDING polyurethane adhesive designed for synthetic materials (e.g. PVC, PU), leather goods, wallets, etc. and for auxiliary works as lining, folding, lasting before sewing or bonding insoles.
AQUATACK 225 Modified natural latex with a better initial strength and faster crystallization than other of the same family AQUATACK 200SR. Sprayable. Contact bonding.
AQUATACK 240-V Modified natural latex for combining and other hand-made auxiliary works in shoemaking, for the production of insoles. High tack and long open time. Soft and flexible adhesive joints. Adequate viscosity to apply by roll or spray gun. Contact bonding.
AQUATACK 300 SL-2 Version of AQUATACK 300SR/ECO with low tack but better resistance to temperature.
AQUATACK 300 SR-ECO Based on synthetic latex. Sprayable. General purpose contact bonding water-based adhesive for auxiliary works (combining, lining, folding, etc.) in shoemaking and leather goods industries, with natural and synthetic materials.
AQUATACK 350-S Version of AQUATACK 300SR/ECO with low tack but better sprayability.
AQUATACK 3835/UV Water based polyurethane adhesive for bonding of leather and synthetic upper materials to leather, PVC, PUR, vulcanized rubber and TR soles, with the suitable previous treatment. Two components. Application by roll or brush.
AQUATACK 400 VISCOSO Based on synthetic latex. General use for the bonding of porous materials in lasting, combining, folding, insole bonding, etc. High viscosity with good brushability. Good tack and 30 minutes open time for contact bonding.
AQUATACK 4000 Water based polyurethane adhesive for bonding Pu foams to upper materials by heat reactivation by iron press to made insoles.
AQUATACK 405 Based on synthetic latex. Sprayable. General purpose contact bonding water-based adhesive for auxiliary works (combining, lining, folding, etc.) in shoemaking and leather goods industries, with natural and synthetic materials.
AQUATACK 4333/PT Polyurethane water base adhesive, similar to AQUATACK 3835/UV but use for bonding of cork/latex (Bios) insoles by spray application, with better hot-tack and lower activation temperature.
AQUATACK 450-S Based on synthetic latex. Medium viscosity with good sprayability. Low tack and good heat resistance for fast and strong contact bonding.
AQUATACK 5000/UV Similar to AQUATACK 4333-PT but with better initial strength and high brightness on BIOS applications.
AQUATACK 6000 Similar to AQUATACK 5000/UV but with very high initial strength and short open time.
AQUATACK L-300 MD For lining uppers, laminating, folding, etc., with natural materials. Sprayable or roll machine. Wet bonding, short open time. Soft and flexible adhesive joints.
AQUATACK L-300 MDE/2 Similar to AQUATACK L-300 MD, but with higher viscosity. Brushable and roll machine.
AQUATACK PRIMER EVA-301/UV Water based Primer for MP-EVA when these are posteriorly bonded with PU water based adhesives, with heat activation at 80-90ºC.